Standards Catalogue

Evidence conservation of failed axle bearings in service

This technical note sets out a methodical approach to collecting data at the point of failure and preserving the failed bearings for further analysis…

Level crossings - drivers' instructions

You will need this module if you carry out the duties of a driver.

Wrong-direction movements

You will need this module if you carry out the duties of a driver or signaller.

Master manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

Possession Workers Manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

Signaller and Signalling Technician Manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

Train Driver Manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

Track Workers Manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

Train Operations Staff Manual

The Rule Book manuals have been produced to provide end-users with access to the content of the Rule Book that is relevant to their roles, e.g.…

ETCS stop marker

This document provides design details for sign AB08 - ETCS stop marker.

AWS EP Repeat & Horn Relay Unit & Base

Signalling into Terminal & Bay Platforms

ATC (AWS) Isolating & Change End Switches

Specification for Thermo-Plastic Insulators for use with Concrete Sleepers Incorporating 'Cast-In' Shoulder Inserts for Pandrol Rail Clips

Nomenclature of Running Signals

Nomenclature of Running Signals

Signal Post Identification Signs

Location of Signal Post Telephones

Wheel Scotches

Identification of Colour Light Signals

Section S - Protection of hand trolleys on running lines not under possession

Section T(iiiA) - Protection of engineering work in sidings

Section W - Bad weather affecting railway infrastructure

Section T(iii) - Protection of engineering work when the engineer takes possession of the line

Section V - Broken rails and bridge strikes

Section A - General responsibilities, safety and security

Section B(iii) - Your general duties when you are on or near the line

Section H(ii) - Working of trains - Out of course working and defective vehicles

Section K - Trains or vehicles detained on running lines and loops

Section P(i) - Working of single lines

Ground position light signal identification plate

This document provides design details for AC09 sign - Ground position light signal identification plate.

ETCS identification plate

This document provides design details for AC11 sign - ETCS identification plate.

GSM-R alias plate

This document provides design details for AC12 sign - GSM-R alias plate.

Permissible speed indicators (km/h)

This document provides design details for AD01k sign - Permissible speed indicators (km/h).

Permissible speed indicators (mph)

This document provides design details for AD01m sign - Permissible speed indicators (mph).

Permissible speed indicators (km/h) for limited clearance

This document provides design details for AD02k sign - Permissible speed indicators (km/h) for limited clearance.

Termination of AWS gap

This document provides design details for AA02 sign - Termination of AWS gap.

Commencement of AWS gap

This document provides design details for AA01 sign - Commencement of AWS gap.

Supplementary sign where crossing is used for animal traffic (PCR diagram 118)

No refuges sign

Code of Practice for Plant Modules on Rail Wagons and Trailers

This Code of Practice identifies the process to be undertaken when plant modules are attached to rail wagons or trailers. This covers the use of plant…

Code of Practice for the Storage and Recommissioning of OTP

This Code of Practice is to define the actions that should be taken for any OTP designated as Out of Service recommending a minimum level of…

Code of Practice for Piling using OTP

This Code of Practice details guidance on the arrangements for controlling the risks when planning and undertaking piling operations on the railway…

Code of Practice for OTM Driver Communication Review Group (CRG)

This Code of Practice supports the national strategy for improved Safety Critical Communications.  It provides a collaborative process (M&EE Group OTM…

Code of Practice for Re-railing Kirow Cranes using Outriggers

This Code of Practice provides guidance in the re-railing of Kirow cranes utilising the crane’s outriggers.

Manually propelled equipment in a line blockage

This poster is provided by the M&EE Networking Group to remind industry of the additional measures to take to use manually propelled equipment in a…

Code of Practice for Haulage Capabilities of On Track Machines

This Code of Practice details the haulage capabilities of on track machines (OTM), it should be followed by any route or operator control when…

Code of Practice for Safe Use of Remote Controls

This Code of Practice identifies the safe use of wired and wireless remote controls for OTP, OTM and other machines in the railway environment. The…

Code of Practice for Action following Hydraulic Pump and/or Motor Failure

This Code of Practice details the details the action to be taken following the failure of an hydraulic pump and/or motor on an on-track machine (OTM).

Code of Practice for M&EE Documents

This Code of Practice details the process by which the M&EE Networking Group produces documentation and is intended for internal use of the M&EE…